Home / English / News / manroland Keen to Be Green

manroland Keen to Be Green

How environment-compatible is your production? Printing companies are increasingly judged by this. Consumable materials from printcom are environment-compatible and contribute to sustainable production.

Above all, specific washing agents and fountain solution help to avoid pollutants and waste or save energy. Here a decisive factor for printcom products is also their environment friendliness that is certified by a national environmental seal of approval or international environment standards.

 

Measured by volume, isopropanol (IPA) is the most significant air pollutant in many printing companies. According to the application, printcom offers specially developed fountain solution additives for alcohol-reduced or alcohol-free printing. printcom fountain solutions are used all over the world, meeting the requirements of different water qualities, as well as special conditions for foodstuff packaging or in critical microbiological environments. However, alcohol-reduced or alcohol-free fountain solution concentrates alone are not enough. Because these agents tend to contaminate faster, the demand for a circulation system that keeps the fountain solution clean for as long as possible is growing. This requires special, easy to install filtration devices that not only delay contamination but also permit longer intervals between changing the fountain solution and reduce the amount that needs to be disposed of. Besides that, the filtration devices work with returnable filter cartridges so no waste is generated through used filters.

 

Currently printcom is developing fountain solution additives that show a considerably reduced buildup of paper particles and ink residue on the blankets and so they need to be washed less often. Besides higher productivity, there is less used washing agent and wash-up paper waste to be disposed of. In most cases, the benefits are greater for webfed presses than sheetfed presses. In an ideal case, wash-ups are reduced by half. The potential savings are not only to be found in longer intervals between wash-ups but also in the time needed for this task. The dosage of solvent additives in the washing agent influences the amount of wash-up fluid mixture that must be disposed of after each cleaning. In principle, washing agents with high-performance additives can be used much more sparingly for removing oil, grease, and dirt than low-dose solvents. This is because high additive washing agents combine spontaneously and stably with water and dissolve printing ink more easily, and the amount of washing agent needed can be reduced by 50 percent or more. Besides the obligatory approval for compatibility with the press and industrial safety regulations, tested washing agents such as those offered by printcom also exactly provide the specified cleaning performance.

 

When the job structure necessitates frequent ink changes, the printing units must be washed-up more often. For pre-cleaning the rollers, printers as a rule use paste that then needs to be removed by a roller washing agent. This procedure doubles washing agent consumption. Part of the residual fluid is waste, but part of it vaporizes to form Volatile Organic Compounds (VOCs) that pollute the working environment. The situation is similar when coatings are used. Volatile isopropanol or water-alcohol mixtures are often used to clean coating circuits, coating plates, and anilox rollers. Besides the safety hazard that comes from the low flashpoint of these materials, the user is exposed to strong fumes. With both inks and coatings, water-based washing agents together with a retrofit provide a suitable alternative. An additional supply circuit in the roller train and a coating cylinder washing device not only speeds up the wash-up process. Because it is automated, washing-up the printing units and coating cylinder is much more user-friendly.

  • Obecnie 0 z 5.
  • 1
  • 2
  • 3
  • 4
  • 5
Ocena: 0/5 (0 ocen/y)

Dziękujemy za ocenę!

Twoja ocena już została uwzględniona. możesz oceniać tylko raz!

Twoja ocena została zmieniona, dziękujemy za ocenę!

Nie masz uprawnień do pisania komentarzy. Zaloguj się.

News

The doors to FESPA Global Print Expo and European Sign Expo 2021, Europe’s leading exhibitions for speciality print and signage, will open in just a few days (12 – 15 October 2021 at the RAI, Amsterdam, The Netherlands). For the first time since Spring 2019, FESPA is welcoming its communities of print service providers and sign makers back to a live event, with a focus on bringing colour back after 18 extraordinary months for these industries.

Elitron will be showcasing the following: Kombo SD+ 31.20: multi-function, digital cutting table with full range of cutting tools for all your digital finishing requirements; Kombo SDC+ 31.20: multi-function, flexible, digital conveyor cutting table with full range of cutting tools for both roll and rigid media and others Elitron Innovations for 2021.

Under the heading ‘New beginnings. New opportunities’, Agfa celebrates the gradual ‘reopening’ of the world and the occasion to present its updated range of inkjet printing solutions live to the European graphic industry at FESPA in Amsterdam (12-15 October).